|
|
|
S.M.A.R.T. attribute list (ATA) This is the list of all known attributes supported by IDE and Serial ATA hard disks. Note: some manufacturers may use the attributes for different purposes also. Attributes not listed here are “vendor specific” attributes (their purpose is not known).
|
| 1
| Raw Read Error Rate | Errors occured while reading raw data from a disk
Indicate problem with the disk surface or the read/write heads.
Critical attribute
|
| 2
| Throughput Performance | General throughput performance of the hard disk
Indicate problem with motor, servo or bearings.
|
| 3
| Spin Up Time | Time needed by spindle to spin-up to full RPM
Indicate problem with motor or bearings.
Critical attribute
|
| 4
| Start/Stop Count | Count of start/stop cycles of spindle
This value does not directly affect the condition of the drive.
|
| 5
| Reallocated Sector Count
(Reallocated Sectors Count) | Count of sectors moved to the spare area
Indicate problem with the disk surface or the read/write heads.
Critical attribute
|
| 6
| Read Channel Margin | Margin of a channel while reading data
The exact function of this attribute is not specified.
|
| 7
| Seek Error Rate | Rate of positioning errors of the read/write heads
Indicate problem with servo, head. High temperature can also cause this problem.
Critical attribute
|
| 8
| Seek Time Performance | Average time of seek operations of the heads
Indicate problem with servo.
Critical attribute
|
| 9
| Power-On Time Count | Total time the drive is powered on
The unit of the measure depends on the manufacturer.
|
| 10
| Spin Retry Count | Retry count of spin start attempts
Indicate problem with motor, bearings or power supply.
Critical attribute
|
| 11
| Drive Calibration Retry Count | Number of attempts to calibrate a drive
Indicate problem with motor, bearings or power supply.
|
| 12
| Drive Power Cycle Count | Number of complete power on/off cycles
This value does not directly affect the condition of the drive.
|
| 13
| Soft Read Error Rate | Number of software read errors
The number of uncorreactable read errors.
|
| 184
| End-to-End error | Number of parity errors during transfer between the cache RAM and the host.
|
| 187
| Reported Uncorrectable Errors | Errors that could not be recovered using hardware error correction methods.
|
| 188
| Command Timeout | Number of aborted operations due to HDD timeout. Value larger than zero may indicate power supply or data cable connection problems.
|
| 189
| High Fly Writes | Number of unsafe write operations outside the normal head flying range.
|
| 190
| Airflow Temperature | Airflow temperature
The temperature of the air inside the hard disk housing.
|
| 191
| Mechanical Shock | Count of problems caused by mechanical shock
Acceleration (for example falling) can cause mechanical shock.
|
| 192
| Power off Retract Cycle | Count of power off cycles
This value does not directly affect the condition of the drive.
|
| 193
| Load/Unload Cycle Count | Count of load/unload cycles
Number of cycles the head moved into landing zone position.
|
| 194
| HDD Temperature | Disk temperature
The temperature inside the hard disk housing.
|
| 195
| Hardware ECC Recovered | Count of correctable errors
Number of errors corrected by the internal error correcting mechanism.
|
| 196
| Reallocation Event Count | Count of sector remap operations
Number of all (successful and failed) remap operations.
Critical attribute
|
| 197
| Current Pending Sector Count | Count of unstable sectors
These pending sectors may be remapped to the spare area.
Critical attribute
|
| 198
| Off-Line Uncorrectable Sector Count | Count of uncorrectable errors when reading/writing
Indicate problem with the disk surface or the read/write heads.
Critical attribute
|
| 199
| Ultra ATA CRC Error Count | Count of errors during data transfer between disk and host
Indicate problem with the power supply or data cable.
|
| 200
| Write Error Rate | Errors occured while writing raw data from a disk
Indicate problem with the disk surface or the read/write heads.
|
| 201
| Soft Read Error Rate | Number of software read errors
The number of uncorreactable read errors.
|
| 202
| Data Address Mark Errors | Number of data address mark errors
Number of incorrect or invalid address marks.
|
| 203
| Run Out Cancel | Number of data correction errors
Invalid error correction checksum found during error correction.
|
| 204
| Soft ECC Correction | Number of corrected data errors
Errors corrected by the internal error correction mechanism.
|
| 205
| Thermal Asperity Rate | Number of thermal problems
Total number of problems caused by high temperature.
|
| 206
| Flying Height | Head flying height
The height of the disk heads above the disk surface.
|
| 207
| Spin High Current | Current value during spin up
The current needed to spin up the drive.
|
| 208
| Spin Buzz | Number of cycles needed to spin up
The number of retries during spin up because of low current available.
|
| 209
| Offline Seek Performance | Drive performance during offline operations
The seek performance of the drive during internal self tests.
|
| 211
| Vibration During Write | Vibration encountered during write operations.
|
| 212
| Shock During Write | Shock encountered during write operations.
|
| 220
| Disk Shift | Distance of the disk has shifted relative to the spindle
Incorrect disk spin can be cause by mechanical shock or high temperature.
|
| 221
| G-Sense Error Rate | Number of mechanical errors
Number of errors resulting from shock or vibration.
|
| 222
| Loaded Hours | Number of powered on hours
This value is constantly increasing (once per every hour).
|
| 223
| Load/Unload Retry Count | Number of load/unload operations
The number of drive head enters/leaves the data zone.
|
| 224
| Load Friction | Mechanical friction rate
The rate of friction between mechanical parts. Indicate problem with the mechanical subsystem of the drive.
|
| 226
| Load-in Time | Total time the heads are loaded
The time while the read/write heads are in the data zone.
|
| 227
| Torque Amplification Count | Rate of torque increase
Torque increase during the spin up operation of the hard disk.
|
| 228
| Power-off Retract Count | Number of power off cycles
The number of times the head was retracted as a result of power loss.
|
| 230
| GMR Head Amplitude | Head positioning amplitude
Head moving distances between operations.
|
| 231
| Hard Disk Temperature | Disk temperature
The temperature inside the hard disk housing.
|
| 240
| Head Flying Hours | Number of head positioning hours
Time spent during the positioning of the drive heads.
|
| 250
| Read Error Retry Rate | Number of retries during read operations
Number of errors found during reading a sector from disk surface.
|
| 254
| Free Fall Event Count | Number of free fall events detected by the accelerometer sensor.
S.M.A.R.T. attribute list (SCSI) This is the list of all known attributes supported by SCSI hard disks. Note: some manufacturers may use the attributes for different purposes also. Attributes not listed here are “vendor specific” attributes (their purpose is not known).
|
| 01
| Buffer over/under run counters
|
| 02_0000
| Write errors corrected without substantial delay
|
| 02_0001
| Write errors corrected with possible delays
|
| 02_0002
| Total write errors
|
| 02_0003
| Total write errors corrected
|
| 02_0004
| Total write errors corrected by algorythm
|
| 02_0005
| Total bytes written
|
| 02_0006
| Total uncorrected write errors
|
| 03_0000
| Read errors corrected by ECC hardware method
|
| 03_0001
| Read errors corrected with possible delays
|
| 03_0002
| Total read errors
|
| 03_0003
| Total read errors corrected
|
| 03_0004
| Total read errors corrected by algorythm
|
| 03_0005
| Total bytes read
|
| 03_0006
| Total uncorrected read errors
|
| 04_0000
| Read reverse errors corrected by ECC hardware method
|
| 04_0001
| Read reverse errors corrected with possible delays
|
| 04_0002
| Total read reverse errors
|
| 04_0003
| Total read reverse errors corrected
|
| 04_0004
| Total read reverse errors corrected by algorythm
|
| 04_0005
| Total bytes read reverse
|
| 04_0006
| Total uncorrected read reverse errors
|
| 05_0000
| Verify errors corrected without substantial delay
|
| 05_0001
| Verify errors corrected with possible delays
|
| 05_0002
| Total verify errors
|
| 05_0003
| Total verify errors corrected
|
| 05_0004
| Total verify errors corrected by algorythm
|
| 05_0005
| Total bytes verified
|
| 05_0006
| Total uncorrected verify errors
|
| 06_0000
| Non medium errors
|
| 07
| Last error event
|
| 0B
| Last deferred error or asynchronous event
|
| 0D_0000
| Temperature
|
| 0D_0001
| Reference temperature
|
| 0E_0001
| Manufacture date (year/week)
|
| 0E_0002
| Accounting date
|
| 0E_0003
| Specified cycle count over device lifetime
|
| 0E_0004
| Accumulated start-stop cycles
|
| 0F
| Application client parameter data
|
| 10
| Self test results log
|
| 18
| Protocol specific port log
|
| 37_0000
| Blocks sent to initiator
|
| 37_0001
| Blocks received from initiator
|
| 37_0002
| Blocks read from cache and sent to initiator
|
| 37_0003
| I/O commands with size smaller than segment size
|
| 37_0004
| I/O commands with size larger than segment size
|
| 3E_0000
| Power on time
|
| 3E_0008
| Remaining minutes until next internal test
S.M.A.R.T. attributes
|